Kimberley2Cape drawer slide handles are the ultimate solution for conveniently unlocking & open drawer & slide units utilizing independent medium or heavy duty locking slides single handed.
With the kimberley2cape drawer slide handle kit you can now effortlessly open your drawers and slides with one hand. Designed for DIY install, the nylon handles have been designed with three heights for your crossbar to be attached.
Now available in type 1 (black) or type 2 (grey) these cover a wide range of drawer slide brands and styles.
Discounted Trade Packs Available. Order the below MOQ (minimum order qty) to qualify for applicable trade pack discounts. Use the following " Trade Pack " discount codes at check out to redeem.
- MOQ 10 = 10% off, discount code Trade Pack 10+
- MOQ 50 = 15% off, discount code Trade Pack 50+
- MOQ 100 = 20% off, discount code Trade Pack 100+
Kit includes
- pair of injection molded glass reinforced nylon handles
- 800mm length of aluminium cross bar tube
- 2 x small stainless steel countersunk screws
- 2 x large stainless steel pan head screws
Required tools
- sharp knife
- philips head screw driver
- small flat blade screw driver
- pencil
- measuring tape
- hacksaw
- soft faced hammer or metal hammer with a piece of timber
- Sikaflex or similar polymer base adhesive
Click here to watch installation video
Click here to download installation instructions
Installation Tip:
- Whilst we have designed these handles to be as close a fit onto the drawer slide unlocking tabs as possible, due to compatibility across a range of drawer slide brands some clearance and movement may be present. To reduce this we recommend injecting the cavity designed to receive the release tab with a polymer based adhesive such as Sikaflex or similar prior to pressing the handles on. This will fill any remaining cavity and aid in the retention and fitment of the handles. Wipe and clean away any adhesive which may be ejected as the handles are pressed on and retainer screw is tightened. Allow the adhesive to fully cure IAW manufactures recommendations prior to drawer slide handle use.
- Whilst it is possible to screw the supplied pan head phillips drive screws into the end of the crossbar tube using a screw driver by hand, it is far easier to run the screws in using an impact driver first to form the internal thread then remove the screws and install between the attached drawer slide handles as per the installation instruction provided.
PLEASE NOTE: the nylon handles are only suitable to be installed on specific lock release tabs shown in the images section. Please ensure you order the black type 1 handles for drawer slides pictured with type 1 handle label and grey type 2 handles for drawer slides pictured with type 2 handle label
Confirmed drawer slide brand compatibility
Type 1 - Black
- UES heavy duty locking slides
- UES medium duty locking slides
- Duraslide heavy duty locking slides
- Duraslide medium duty locking slides
- Dunn & Watson 125kg Hercules Series locking slides
- Dunn & Watson 227kg Titan Series locking slides
Type 2 - Grey
- IRS heavy duty locking slides
- IRS medium duty locking slides
- Dorset heavy duty locking slides
- Shanghai Hypal Hardware Products Co Ltd heavy duty locking slides
Disclaimers
- most medium duty locking slides are designed to come apart at the end of their travel, accidental disassembly of the slides may occur if the crossbar or drawer slide handles are not released before the slides are at full extension. This may result in the drawer or slide body dropping causing personal injury or damage to the product or vehicle it is installed on. It is the responsibility of the purchaser to install a stopper is installed to prevent over travel and accidental disassembly as explained above.
- When closing any drawers or slides always check to ensure the handles and crossbar have engaged in the latched position correctly.
- Installation of the nylon handles onto heavy duty locking slides requires increased care and attention and must be carried out in accordance with the installation instructions provided with the kit.
Warranty Terms & Conditions
NQ Ally Works Pty Ltd warrants to the original purchaser that the Kimberley2Cape Drawer Slide Handle Kit is free from defects in material and workmanship, for the term described below, except as qualified below.
Intended Use
The Kimberley2Cape Drawer Slide Handles are intended for use on specific drawer slides only as pictured and listed. The drawer slide handles or drawer slide latch tabs should not be modified to allow fitment. Doing so voiding all warranties.
Warranty Terms
24 Months manufacturer’s warranty from the date of purchase.
What Is Covered
In the event that any component is found to be defective due to material or workmanship during the 24 month manufacturer’s warranty period, NQ Ally Works Pty Ltd will replace the component or offer a refund of the original item amount. Before replacement or refund can be authorized the original purchaser is required to email us at nqallyworks@outlook.com or info@kimberley2cape.com.au stating reason for request including photos of defective nature. The complete kit must be returned and receive back to NQ Ally Works Pty Ltd postage paid by the sender. NQ Ally Works Pty Ltd may only authorize and process refund once goods are received.
What Is Not Covered
NQ Ally Works Pty Ltd shall only be liable for warranties relating directly to the Kimberley2Cape Drawer Slide Handle Kit. NQ Ally Works Pty Ltd shall not be liable for or assume liabilities, warranties, responsibilities or costs relating to defects or damage arising on or associated with any drawer units, slide units, drawer slides or vehicles to which the Kimberley2Cape Drawer Slide Handle Kit is installed on. Defective components or improper operation of the Kimberley2Cape Drawer Slide Handle Kit or drawer units, slide units, drawer slides or vehicles to which the Kimberley2Cape Drawer Slide Handle Kit is installed on where installation is not carried out in accordance with the installation guide and instructions are not covered by the 24 Months manufacturer’s warranty. Kimberley2Cape or NQ Ally Works Pty Ltd will not be liable for any injury or damages resulting from failure to adhere to the requirements stated in the included disclaimers or installation instructions.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS LIMITED WARRANTY. IN NO EVENT SHALL NQ ALLY WORKS PTY LTD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
Return policy: 25% restocking fee applies.
Sale & purchase is subject to Terms Of Service policy
Features & Inclusions
Specifications
Shipping info
Pairs well with